Toro Mini 8 Series Bedienungsanleitung PDF herunterladen

The Mini 8 rotor is designed for residential and light commercial

installations. It comes in three sizes, 4" pop up, 6" pop up and 12" pop up.

Nozzling Up The System

The 1.5 GPM nozzle comes pre-installed from the factory. A nozzle tree

consisting of four additional nozzles is provided with each rotor (

Figure 1).

Please see the nozzle performance chart for flow rates. By using various

combinations of nozzle flow rates, you can balance the sprinklers to

achieve approximately the same precipitation rates.

Every case of Mini 8 product contains two Mini 8 rotor keys. The Mini 8 key

is used to pull up the riser, to remove the nozzle, to reduce the radius and

to adjust the arc (

Figure 2).

To Extract/Insert A Nozzle

Use the winged portion of the key to pull the riser up in order to access the

nozzle orifice. Insert the key into the pull-up hole (

Figure 3), turn it 90˚, and

pull up. Hold the riser in the pulled up position.

Using the end of the key, turn the radius adjustment screw

counterclockwise until it clears the top of the nozzle. See Figure 4A.

Insert the key into the nozzle right side slot with the pointed end of the key

facing upwards. Use the point to extract the nozzle out. See

Figure 4B.

To install a nozzle, press the nozzle into the nozzle socket (

Figure 5A).

Turn the radius adjustment screw clockwise to its desired location ensuring

that it is in a position to hold the nozzle in place even if radius reduction is

not required (

Figure 5B).

To Set The Arc

The Mini 8 rotor arc is pre-set from the factory.

The Mini 8 rotor has a fixed LEFT stop. To find the left stop position,

rotate the nozzle turret clockwise (to the right) until it stops, then rotate the

nozzle turret all the way back to the left.

To increase the arc, insert the key into the arc adjuster shown in Figure 6.

Hold the turret in place while turning the tool clockwise. Keep turning until

the arc indicator arrow points to the desired arc angle.

As an example indicated in Figure 7, the arc is set to 270˚. The sprinkler

will then water from the left stop and rotate clockwise (see

Figure 8) until

270˚, the adjusted right stop, is reached. The sprinkler will then return back

to the left stop and repeat the cycle.

To decrease the arc, insert the key into the arc adjuster. Hold the turret in

place while turning the tool counter clockwise. Keep turning until the arrow

points to the desired arc.

To adjust the arc while the rotor is running, turn the turret gently in the

direction that it is spraying. Once the left stop has been located, follow the

directions above to increase or decrease the arc.

To line up the left stop with landscape features which define the left side of

the irrigated arc, simply turn the housing cannister and point the left stop

towards the desired direction. You may also pull the riser up with the key

and rotate the LOWER portion of the riser until the left stop is at the

desired position.

DO NOT rotate the TOP portion of the riser.

Installation Tips

CAUTION: The Mini 8 rotor is designed for use in clean-water irrigation

systems only. Sprinkler component damage or malfunction can occur

if operated with any other water source.

The Mini 8 rotor should be installed with

the cap at the finished grade. It is not

designed to be installed below grade.

See

Figure 9.

The radius adjustment screw can be used

to reduce the radius throw by up to 25%.

You should note that this does not reduce

the flow of the nozzle.

Screen Maintenance

The screen can be accessed through the

bottom of the riser. Remove the cap of the

Mini 8 and lift the riser assembly out of the

housing cannister. If plugged, the screen can

be removed, cleaned, and re-inserted into

the riser.

Mini 8 Nozzle Performance

For Product Inquiries:

The Toro Company

5825 Jasmine Street

Riverside, CA 92502-0489

Tel: (909) 688-9221

(800) 225-2839

Mini 8, Gear Driven Sprinkler

User’s Guide

.75

GPM

1.0

GPM

1.5 GPM

2.0 GPM

1.0

.75

1.5

3.0

2.0

3.0 GPM

Figure 1 Figure 2

Nozzle Tree

Mini 8

Rotor Key

Arc Adjuster

Pull-Up

Keyhole

Arc Angle

Indicator

Radius Adjustment/

Nozzle Retention

Screw

Figure 3 Figure 4 Figure 5

Figure 6 Figure 7 Figure 8

Increase

Decrease

Left Stop Position

Angle Indicator

Points To 270˚

Left Stop

Position

Adjustable

Right Stop

Position

(270˚)

Figure 9

Screen

4" Pop Up

6" Pop Up

12" Pop Up

Nozzle

(Gallons)

0.75

1.0

1.5

2.0

3.0

Pressure

(PSI)

Flow

(GPM)

0.8

0.9

1.2

1.1

1.3

1.5

1.2

1.4

1.6

1.4

1.7

2.0

2.3

2.6

3.0

Radius

(Feet)

Pressure

(kPa)

207

276

345

207

276

345

207

276

345

207

276

345

207

276

345

Flow

(L/M)

3.03

3.41

4.54

4.16

4.92

5.68

4.54

5.30

6.06

5.30

6.43

7.57

8.71

9.84

11.36

Flow

/H)

0.2

0.3

0.2

0.3

0.4

0.3

0.4

0.5

0.6

0.7

Radius

(Meters)

5.8

6.1

6.4

6.7

7.0

7.3

7.9

8.5

9.1

9.4

9.8

10.1

10.4

10.7

Inhaltsverzeichnis

Seite 1 - User’s Guide

The Mini 8 rotor is designed for residential and light commercialinstallations. It comes in three sizes, 4" pop up, 6" pop up and 12" p

Kommentare zu diesen Handbüchern

Keine Kommentare

Toro Mini 8 Series Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein Toro Mini 8 Series herunter. Toro Mini 8 Series User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Toro Mini 8 Series