Toro Multi-Program Automatic Timer (53869) Bedienungsanleitung PDF herunterladen

Blue Stripe

Drip Multi-Program Automatic Timer

You have purchased a quality, multi-program automatic hose-end timer that uses an efﬁcient solenoid snap-on/snap off valve. Please read these operating instructions carefully in order to

become familiar with the features, correct installation, and use of the timer. Verify that the timer performs as programmed when used for the ﬁrst time. This timer should only be operated by

adults who are familiar with the operating instructions.

Designed Use This timer is designed for use outdoors only for the control of sprinklers and water systems. The timer is not suitable for use: 1) If your water pressure exceeds 145 psi (10 bar);

2) If you use a well, bore, or unﬁltered water supply; 3) If you use any type of pump to draw water; 4) For any commercial/industrial application; and 5) In conjunction with chemicals, foodstuffs,

ﬂammable, or explosive materials.

How the Electronic Timer Works Your automatic timer will water your garden and hanging baskets automatically according to the program you choose. You can set the timer to water your

garden early in the morning or late at night when water evaporates the least. It will continue to water while you are away. It provides two ﬂexible methods to control irrigation:

1. Manual: Press Man/Auto button to switch between: On - Off - Auto (you will hear a click when on; off is silent).

2. Automatic: Can water up to 8 times per day. Choose quickly from 15 different day combinations to control which days of the week the timer operates.

Installing the Battery (see Figure 1)

1. Remove the timer face by pressing the release button on the underside of the timer.

2. Remove the battery cover and gasket (secured by two screws).

3. Connect a 9V battery (not included) to the battery terminals.

4. Install the battery cover and gasket. Make sure the gasket is properly aligned. Secure battery cover (two screws).

5. We recommend planning and recording your watering programs before programming the timer.

6. Set the current day and time

7. Set the desired watering programs

8. Re-install the timer face.

9. Attach the timer to the water tap. For 0.75" (20mm) – attach directly. For 1" (25mm) – remove 0.75" (20mm)

threaded bushing.

Note: Timer must only be mounted in a vertical position with the connector nut pointing vertically upwards

10. Attach the hose to threaded outlet or attach 0.710 compression ﬁtting to connect Blue Stripe

Drip 1/2" (13mm)

tubing.

11. Do not use tools! Tighten connections by hand only – do not over tighten!

Programming the Timer

1. Press “Program” once. Program 1 ON appears on the display (see Figure 3).

2. Press “Hour” and “Minute” to set start time, program 1 (24hr clock; see Figure 4).

3. Press “Day” to set days of the week that program 1 operates. (defaults to Mon-Sun, i.e. every day).

4. Press “Program” again. Program 1 OFF appears on the display (see Figure 5).

5. Press “Hour” and “Minute” to set ﬁnish time, program 1 (see Figure 6).

If you only want your watering system to activate once per day, for the Days set in step 3 above,

stop here.

6. Press “Program” again. Program 2 ON appears on the display.

7. Repeat steps 2 through 5 above for a second watering program on the above days, or watering on

selected days only.

• Up to 8 programs may be set from a total of 15 different day-of-the-week conﬁgurations

• Ensure that the days for the OFF setting are the same as those for the ON setting

• Ensure that every ON time has an OFF time!!

• To exit programming press “time” which returns the display to the current time and day

If after pressing “Program” you press “Day” repeatedly the following day combinations appear (see step 3 above)

To ensure long life and prevent damage to the automatic timer

• Use with cold, main connection water only. Check the ﬁlter as necessary.

• Avoid tension or pulling on the hose leading or drip tubing from the timer.

• We recommend removing the timer from the tap during cold months, particularly where temperature drops below 41°F (5°C). The timer must not be subjected to freezing temperatures or frosts.

• Do not use the timer if it is likely to be subject to more than ‘seasonal’ amounts of water (eg. In the path of sprinklers or other emitter or with a leaking tap).

Technical Data

Power: One 9-volt alkaline battery (use a high power alkaline battery)

Battery life: 1 season (6 months) normal use.

Recommended operating temperature: 41°F – 100°F (5°C to 38°C)

Recommended water pressure: 21 PSI – 100 PSI (1.4 bar to 6.9 bar)

Maximum operating pressure: 145 PSI (10 bar). In higher pressure areas, use a pressure reducer from the tap.

Understanding the Multi-Program Automatic Timer (see Figure 2)

Control Keys

1. Time – used to set current time of day and return to clock

screen. Press and hold to set the current time and day.

2. Min – used to set minutes of current time and watering

start/ﬁnish times. Press to advance one minute.

3. Hour – used to set hour, current time, and watering

start/ﬁnish times. Press to advance one hour.

4. Day – used to set current day and watering days.

Press to advance to next day.

5. Man/Auto – used to select between manual on/off and

automatic watering mode.

6. Prog – used to set or change stored watering programs.

Note: If the timer is left in programming mode for 1 minute

without any selections made, the timer will return to

automatic mode.

7. Esc – used to clear programs in programming mode or to

set the keypad lock. To lock the keypad, hold Esc for

more than 3 seconds. Hold again for 3 seconds to

unlock the keypad.

8 9 10

1 2 3 4

1 MO

2 TU

3 WE

4 TH

5 FR

6 SA

7 SU

8 MO

9 TU

11 MO

12 TH

SA SU

11 MO

TU WE TH FR SA

MO TU WE TH FR

MO TU WE TH FR SA SU

Figure 1

Battery Cover

and Gasket

9V Battery

Timer Face

Release Tab

25mm

Fitting

20mm

Bushing

Figure 2

Figure 3

Figure 5

Figure 4

Figure 6

Functions

All functions can be selected by pressing the Man/Auto button.

8. ON – when selected, an arrow appears above ‘ON’ on the

display panel. The valve will open and watering will commence

immediately.

9. Auto – when selected, an arrow appears above ‘AUTO’ on the

display panel. The timer is in Automatic Mode and watering will

occur according to the programs set by the User.

10. OFF – when selected, an arrow appears above ‘OFF’ on the

display panel. The valve is shut off and water is prevented from

ﬂowing from the timer. In this mode, no watering will take place.

Display Symbols

11. Day of Week – indicates the current day of the week in

Automatic Mode and watering days selected for calendar

watering program mode.

12. Batt. – low battery symbol displayed when the battery is low.

13. Display Lock (A and a) – indicates that the keypad has been

locked. Prevents changes being made to set programs, current

time, and manual activation.

14. Program – indicates program number in programming mode.

1 2

Blue Stripe 1

Inhaltsverzeichnis

Seite 1 - Blue Stripe

Blue Stripe® Drip Multi-Program Automatic TimerYou have purchased a quality, multi-program automatic hose-end timer that uses an efﬁcient solenoid sna

Seite 2

Blue Stripe® Drip Programador de Electrónico MultiprogramaHa adquirido un programador de electrónico multiprograma de alta calidad que emplea una válv

Kommentare zu diesen Handbüchern

Keine Kommentare

Toro Multi-Program Automatic Timer (53869) Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Elektrische Zeitschaltuhren Toro Multi-Program Automatic Timer (53869) herunter. Toro Multi-Program Automatic Timer (53869) User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern