GreenKeeper 212 Features:• Easily Expandable Up To 12 Stationswith 2-Station Plug-in Modules•3 Watering Programs With:- Calendar, Interval and Odd/Eve
Selecting Program Start TimesA program start time is the time of day you select tobegin an automatic program watering cycle. It is important to rememb
It is always helpful to plan your watering schedule onpaper before beginning the programming steps. You willhave a record of your watering schedule an
11(Example)
12SU MO TU WE TH FR SA SU MO TU WE TH FR SA SU MO TU WE TH FR SA 1123456789101112 23 456 7 123 456 7123 456 7CALENDARLOCATIONZONESTATION RUN TIME STA
The GreenKeeper 212 utilizes a 9-volt battery to retain itswatering program information in the event of a main powerinterruption. This battery backup
24-Hour Clock ModeThe GreenKeeper 212 is set to display time in the 12-hour clock mode. If youprefer to use a 24-hourclock mode (military time),select
15The GreenKeeper 212 program memory can be reset tothe permanent program values or cleared completely atany time without removing power. Resetting th
16Note: To select the 24-hour clock mode, see page 14.Turn the control dial to the CURRENT TIME/DAYposition (the hour digits will begin flashing).To a
For each program, you can select Calendar, IntervalOdd, Even or Off. To set a Calendar schedule, continuehere. To set an Interval schedule see page 18
Setting an Interval ScheduleTurn the control dial to the WATERING DAYSposition. Check the PROGRAMS switch setting. If necessary,reposition the switch
Introduction and Set Up GreenKeeper 212 Components...2-5 Sprinkler System Basics...6 Watering P
Setting an Odd or Even Schedule Note:The Odd/Even Selector Jumper must be removedfor this type of watering schedule. See page 14 for details.Turn the
Turn the control dial to the PROGRAM START TIMEposition. Check the PROGRAMS switch setting. If necessary,reposition the switch to select the desired p
Turn the control dial to the STATION TIMESposition. Check the PROGRAMS switch setting. If necessary,reposition the switch to select the desired progra
Note: The GreenKeeper 212 indoor controller is notweather resistant and must be installed indoors or ina protected area. For outdoor installation of a
1. Route the valve control wires between the valves andthe controller.Note: Using 18 AWG (1.0mm2) multi-wire sprinklervalve connection cable is recomm
(Optional)CAUTION: To prevent controller damage,ensure the relay current draw does not exceed0.30 Amps. Do not connect the controller directly to the
1. Remove the lower housing cover (A) by pulling outward on the handle.2. Remove two phillips screws from the transformeraccess cover (B). Pull the co
1. For safe, reliable operation, select an installation sitewhich will provide the following conditions:• Protection from irrigation spray, exposure t
1. Route the valve wires or wire cable from the valves,into the controller cabinet.Note: Using 18 AWG (1mm2) multi-wire sprinklervalve connection cabl
(Optional)CAUTION: To prevent controller damage,ensure the relay current draw does not exceed0.30 Amps. Do not connect the controller directly to the
Controller ComponentsGreenKeeper 212 Introduction and Set Up21 3 BATTERY2
(Optional)The Toro Rain Switch is a remote rain sensor which canbe connected directly to your GreenKeeper 212 to auto-matically interrupt watering dur
The GreenKeeper 212 controller has three modes ofoperation: Automatic, Manual and Off. In the Automaticmode the controller tracks the time and day and
Manual operation enables the automatic watering pro-grams or selected stations assigned to the program to bestarted manually. During operation, tempor
The following watering control features enable you to fur-ther control the watering program during operation.All watering control features apply to wa
When the control dial is turned to the OFF position, thecontroller immediately shuts off any watering operationcurrently in progress. Leaving the cont
Changes in season and temperature generally require achange in station run time to maintain a healthy land-scape and conserve water. The season adjus
The fuse protects the controller from damage due topower surges and excessive current draw through theStation Modules. Before replacing the fuse, chec
36If you are having a problem with the controller, check the following symptoms, possible causes and remedies. If the problem cannot be resolved or yo
Cabinet Dimensions:Indoor Model7.5" W x 8.5" H x 2" D (19cm W x 21.6cm H x 5cm D)Outdoor Model13.25" W x 9" H x 3.5" D (
Domestic: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These l
GreenKeeper 212 Components The following are brief descriptions of the controller com-ponents and display elements. Each of these items willbe explain
Controller Components 3 - Control Dial Positions (continued)SEASON ADJUST – Enables the run time of allzones in a program to be simultaneously increa
5BATTERYMANUALSTARTONNEXTOFFPROGRAMSBCA16181920BATTERY16171856710111213149 8 15 3 4 Controller Components
The three main components of every automatic sprinklersystem are the controller, station control valves andsprinklers. The controller is the brain of
A watering program requires three basic instructions tooperate automatically:• What days to water –called watering days• When to water – called a prog
This section covers in detail each of the three parts of awatering program – watering days, program start timesand station run times. Selecting Wateri
Kommentare zu diesen Handbüchern